• If you would like to have the best heatpress…then you have found the right place!
  • UV-tulostimella tulostat suoraan kappaleiden pintaan.
  • Kun haluat parhaan. Monipuoliseen merkintään ja leikkaukseen - Epilog Laser. Made in USA
  • UV-hybridtulostimella tulostat suoraan tasolle tai rullalle
  • Rolandin uusin 4-väritulostin mallisto ammattilaisille
  • Supersuosittu tarraleikkurimme lyömättömään hintaan. Tutustu!
  • Rolandin uuden sukupolven leikkaavat suurkuvatulostimet
  • Epsonin helppous ja laatu nyt DTG-tulotimessa.
  • Tekstiilitulostamisen uusi aikakausi
  • Työpöydälle sopiva A4 koon kaiverruskone erinomaisella ohjelmalla. Vain 4700 €. Made in Japan

3M Scotch-Weld DP-8005 akryyliliima

Etusivu > TEOLLISUUSTEIPIT & LIIMAT > Tukkuerät 3M > Scotch-Weld EPX -rakenneliimat ja nokat

3M Scotch-Weld DP-8005 akryyliliima
Tuotekoodi
7000079932
Valm. tuotekoodi
L8005265
Toimituskulut alk.
856,50 €
ALV 0,00 %
kpl

Vaalea
265 ml
6/pakkaus

3M™ Scotch-Weld™ Structural Plastic Adhesive 8005 is one of our 10:1 ratio, two-part acrylic based adhesive specially formulated to bond many low surface energy plastics. It will adhere many grades of polypropylene, polyethylene, and thermoplastic Elastomers (TPE`s) without special surface preparation.

- Ability to structural bond low surface energy plastics such as polyolefins, polypropylene, polyethylene and TPO's
- Excellent resistance to water and humidity combined with very good chemical resistance results in a bond that can withstand a variety of applications and conditions
- Cures at room temperature without heat or other chemicals to eliminate complex adhesion processes
- One step process results in a strong bond on low surface energy plastics minimizing or eliminating pre-treatment or preparation of the substrates needed prior to bonding
- Solvent-free adhesive system

3M™ Scotch-Weld™ Structural Plastic Adhesive 8005 was designed to handle adhesion problems typically associated with the bonding of low surface energy plastics. In addition to various plastics, it will also bond a variety of other dissimilar substrates ranging from metals, rubber, glass, ceramics and wood in a one-step process with minimal or no surface preparation. However, all substrates should be clean, dry and free of paint, oxide films, oils, dust, mold release agents and other surface contaminants.

This adhesive is a medium viscosity structural adhesive with good control and spread to sufficiently wet out the surface when applied. With a 10:1 mix ratio it provides a 3 minute work life. Handling strength is reached in approximately 3 hours and the adhesive will fully cure in 24 hours at room temperature (72°F /22°C.) Once bonded this adhesive features excellent water and humidity resistance while maintaining very good chemical resistance. It is an effective system for joining, potting and structural bonding, and can replace screws, rivets, plastic welding and two-step processes which include chemical etchants, priming or surface treatments in many applications.

Recommended Applications:

- Joining plastics to metals, such as in the manufacture or repair of appliances
- Bonding low surface energy plastics without priming
- Impact resistance composite bonding
- Manufacture or repair of various sporting goods equipment
- Low surface energy plastics such as polypropylene, polyethylene and thermosplastic elastomers

Acrylic adhesives are two-part adhesives that provide excellent bond strength and durability, although slightly lower than epoxy adhesives. However, they have several features that make them easier to use, including a much faster cure speed, higher tolerance for oily or unprepared bonding surfaces and the ability to bond a wide variety of materials, including nearly all plastics. Newer acrylic adhesive formulations are room temperature stable with a long shelf.

Adhesion Strength‎ ‎ 270 oz/in,‎ 140 oz/in
Adhesive Type‎ ‎ Acrylic
Applications‎ ‎ Shroud Attachment,‎ Bonding
Brand‎ ‎ Scotch-Weld
Color‎ ‎ Black,‎ Off-White
Consumer Label‎ ‎ No
Full Cure‎ ‎ 8-24 Hours @ 72 F (22 C)
Hardness‎ ‎ 55-60 Shore D
Industries‎ ‎ Transportation,‎ Specialty Vehicle,‎ Construction,‎ Automotive,‎ Military & Government,‎ General Industrial,‎ Electronics,‎ Consumer Goods
Mix Ratio Volume Base:Accelerator‎ ‎ 10 : 1
Open Time‎ ‎ 3 minutes @ 72 F (22 C)
Physical Form‎ ‎ Flowable Liquid
Product Form‎ ‎ Gallon,‎ Cartridge
Product Type‎ ‎ Structural Plastic Adhesive
Shear Strength at 72 Degrees F (22 Degrees C)‎ ‎ 2000 Pound-Force Per Square Inch,‎ 2200 Pound-Force Per Square Inch
Shelf Life in Months (from date of manufacture)‎ ‎ 6
Specific Gravity‎ ‎ 0.99,‎ 0.98
Storage Temperature‎ ‎ 40 Degree Fahrenheit
Substrate 1‎ ‎ Plastics (High Performance Nylon),‎ Plastics (ABS, PVC, Acrylic),‎ Metal,‎ Plastics (Polyolefins and Thermoplastic Elastomers),‎ Glass & Ceramics,‎ Wood & Hardboard
Substrate 2‎ ‎ Plastics (High Performance Nylon),‎ Plastics (ABS, PVC, Acrylic),‎ Metal,‎ Plastics (Polyolefins and Thermoplastic Elastomers),‎ Glass & Ceramics,‎ Wood & Hardboard
Substrates‎ ‎ Plastics (High Performance Nylon),‎ Plastics (ABS, PVC, Acrylic),‎ Metal,‎ Plastics (Polyolefins and Thermoplastic Elastomers),‎ Glass & Ceramics,‎ Wood & Hardboard
Viscosity Range (cps) at Room Temperature‎ ‎ 15,000-30,000,‎ 35,000-55,000,‎ 25,000

tech
tech

AAA-luokitus

3M

Roland

Epson

Epilog

Epilog

Powered by Clover Shop® - www.clovershop.com